Lee County

239-768-3667

Collier County

239-643-3667

Charlotte County

941-627-0150

Southwest Florida

800-375-3667

Dock and In-Plant Lifts

in Cape Coral, Fort Myers, Estero, Bonita Springs, Lehigh Acres, Marco Island, Naples, Port Charlotte, North Port, Punta Gorda, Venice and Sarasota

Serco Level Lift Model

High-performance dock leveler — it provides the same performance benefits of a hydraulic dock leveler such as regenerative hydraulics, powered lip control, safety velocity fuse and push-button controls

Below-dock operation — In scissor mode, it eliminates the steep grade differences between the vehicle bed and the leveler deck, providing safe, level, below-dock operations

Scissors lift versatility — Unlike standard scissor lifts, the hydraulically powered dock lip ensures faster cycling times and its lifting capacity can handle the toughest loads while also providing dock-to-grade-level forklift access

  • 50,000 lbs. Capacity Leveler (per ANSI MH14.1-1987)
  • 12,000 lbs. Capacity Lift (8 ft. long units)
  • 20,000 lbs. Capacity Lift (10 & 12 ft. long units)
  • 18″ Lip Standard
  • LED Light Communication Package
  • Remote 7.5 HP Independent Lift Motor & Hydraulic System
  • PLC Operation
  • 1 HP Independent Leveler Motor & Hydraulic System
  • Full Feature NEMA 12 Control Panel with Mushroom Style Stop Button
  • Remote NEMA 4X Pendant Push Button Hand Control
  • Interior Warning Light & Audible Alarm Indicate Dock Lift Is Not In Stored Position
  • Safety Velocity Fuse on Leveler and Lift
  • Guard Rail Package
  • Rear Hinge Blocks
  • Protective Roller Curtain on Front
  • Side and Rear Weatherseal
  • Grease Fittings
Serco Level Lift Model
Serco Rail Lift Model

Serco Rail Lift Model

  • Low Profile for Surface-mounted Applications z No Pit Construction Required
  • Three-sided Platform
  • Heavy-duty I-beam Deck Understructure
  • Excellent End-load Stability in Fully Raised Position z Displacement style Cylinder with Internal Stops
  • Self-contained Power Unit/control Panel
  • Standard Pre-wired Control Panel
  • NEMA 4X Push-button Controller with 15’ Cord
  • Superior Speed-to-horsepower Ratio Compared to Scissor-style Dock Lifts
  • Direct thrust Cylinders Provide Constant Speed Through Full Range of Travel
  • Checker Plate or Smooth Deck Surface z Sealed Guide Bearing Rollers
  • Fused 24-volt Control Circuit

Serco Loadwarrior Air Lift Model

  • No lag down, portable design
  • Pallet jack pockets built in
  • Removable gibs
  • Over-pressure relief valve
  • Operating angle from horizontal to 30 degrees from horizontal
  • Heavy-duty airbag
  • Downspeed flow control
  • Works on “shop air,” 80psi
  • Includes a hand or foot valve control and a 6′ hose
  • Meets or exceeds the ANSI MH29.2 standard for industrial scissor lift
Serco Loadwarrior Air Lift Model
Serco Loadwarrior Turntable Model

Serco Loadwarrior Turntable Model

Manual or powered models are available to efficiently palletize, build-up and break-down, and either can be mounted on a scissors lift, stable bench, or other surface. In addition, ground-mounting is also available.

  • Rigid base frame with predrilled mounting holes
  • 1/2″ thick steel platform with rounded corners
  • Tough TGP hard-chromed kingpin
  • Rollers are sealed ball bearings for ease of operation
  • Roller-pin bushings are self-lubricating
  • 34″ x 34″ is minimum turntable size

Serco Scissors Dock Lift Model SDL68-5

Our Dock Lifts can accommodate a wide variety of truck styles; from 20″ step vans or pick-up trucks to high cube vans, standard semi-vehicles and 60″ high stake bed vehicles. They can be pit or surface-mounted inside the building or in front of the loading dock. (Surface-mounted dock lifts can be relocated if used in applications where a pit or permanent installation is prohibited.)

  • Beveled toe guards
  • 18″ standard solid or split bridge plate
  • Dual hydraulic lifting cylinders for optimum performance
  • Velocity fuses on lift cylinders prevent uncontrolled descent
  • Removable, mandrel-formed tubing handrails
  • Maintenance safety strut
  • Safety tread steel deck
  • Safety chains across operating ends
  • Upper travel limit switch
  • Available in 4,000-20,000 lb. capacities
Serco Scissors Dock Lift Model SDL68-5
Serco Loadwarrior Double Scissors Table Model

Serco Loadwarrior Double Scissors Table Model

  • Pre-wired power unit with UL approved control components
  • Internally mounted 5 hp power unit
  • Self-lubricating composite bearings
  • Solid steel legs with stiffener bars
  • Turned, ground, polished and hard-chromed axle pins
  • Double-wire braided hydraulic hoses
  • Velocity fuses on all cylinders to prevent uncontrolled descent
  • Polyethylene reservoir allows easy visual check of oil level
  • Maintenance locks built into base frame
  • Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts

Serco Loadwarrior Tilter Model

  • Pre-wired power unit with UL approved control components
  • Power unit internally mounted
  • Available in 1 1/2 hp three-phase or 3/4 hp single-phase with 24V AC control valve
  • Self-lubricating composite bearings
  • Velocity fuses on all cylinders to prevent uncontrolled descent
  • Double wire braided hydraulic hoses
  • Polyethylene reservoir allows easy visual check of oil level
  • Maintenance locks built into frame
  • Standard 12′ high lip
  • 28″ W x 38″ L minimum platform size
  • Meets or exceeds the ANSI MH29.2 standard for industrial tilters
Serco Loadwarrior Tilter Model
Serco Loadwarrior Scissor Table Model

Serco Loadwarrior Scissor Table Model

  • Solid steel legs with stiffener bars for extra strength and support
  • Polyethylene tank prevents condensation, provides easy check of oil level
  • High-pressure cylinders with safety velocity fuses to prevent uncontrolled descent
  • Pre-wired NEMA-rated controls
  • High-strength roller pins with snap rings
  • Hardened steel rollers
  • High-strength steel polished axle pins
  • UL-approved control components
  • Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts

Serco Loadwarrior Air Tilter

  • Reinforced, heavy-duty airbag
  • Air damper reduces platform bounce
  • Fork pockets for simple mobility
Serco Loadwarrior Air Tilter
Southworth Model SR-44 Pallet Rotator

Southworth Model SR-44 Pallet Rotator

With the ability to handle pallet loads measuring up to 48″ x 48″ x 60″ high; the Southworth Product Corp PalletPal Pallet Inverter / Rotator is a simple, rugged machine designed to invert entire pallet loads. The pressure adjustable clamping mechanism easily secures loads up to 4,400 pounds and rotates them 180 degrees on a massive anti-friction turret bearing. Here are just a few uses:

  • Replace broken pallets
  • Switch loads to/from in-house or shipping pallets
  • Transfer from pallets to slip sheets
  • Replace damage goods at the bottom of the load

Other clamp openings are available, consult Southworth’s sales department for details.

TKO
Rytec
lifestyle screen
Decovac
APS Resource
SERCO
Door Imagination
Warranty
Clopay
LiftMaster

Action Automatic Door & Gate is a Proud Member of

MS BIA
BIA
CBIA
Angie List
Cellphone for Soldiers
IDA