Inflatables

in Cape Coral, Fort Myers, Estero, Bonita Springs, Lehigh Acres, Marco Island, Naples, Port Charlotte, North Port, Punta Gorda, Venice and Sarasota

You are here:

Serco SI450 Inflatable Dock Shelter

DESIGN HIGHLIGHTS

Standard Frame Projection: 24″ Side Frame / 34″ Head Frame
Standard Air Bag Fabric: 10 oz. Vinyl
Standard Side & Head Storage Curtain Fabric is 22 oz Vinyl & Includes Fiberglass Stays
Head Storage Curtain Includes Yellow Guide Stripes on 8′-6″ Centers
Side Curtains Are 16″ Wide; Head Curtain is 26″ High at Peak of Head Frame
Frames Are Pressure Treated Wood
Side Frames Are 2 x 4, Head Frame Has 2″ Rake with
2 x 10 Front & 2 x 6 Back
Standard Head Bag Drop is 36″, 42″ or 48″ From Underside of Head Frame.
Standard Front Opening Width is 7′-6″
Steel Supports Project 5″ Greater than Side Frame Projection
Includes Foam Filled Draft Pads in Bottom Corner
Blower Motor: 1/2 HP, 115V with Automatic Reset Thermal Overload Protection (includes NEMA 1 switch)

Rigid Frame Specifications

Serco SI400 Inflatable Dock Shelter

Design Highlights

Standard Side Member Projection: 24″
Side Member Face Width: 12″
Side Member Backing: 2×8 Pressure Treated Wood
Standard Cover Fabric: 10 oz. Vinyl
Standard Head Member Projection is 10″ Greater than Side Member Projection
Front of Header Assembly is 2×8
Top of Head Frame Has Upward Taper & Requires 2-1/2″ Clearance Above Unit Height
Blower Motor: 1/2 HP, 115v with Automatic Reset Thermal Overload Protection (includes NEMA 1 switch)
Guide Stripes on Head Storage Curtain on 8′-6″ Centers
Head Member Mounting Flanges Require 2″ Clearance on Either Side
Head Member Consists Fiberglass Covered Treated Wood Frame Which Supports Integral Torsion Spring-head Bag Assembly (standard head bag drop is 36″ to 48″)

Serco SI350 Inflatable Dock Seal

DESIGN HIGHLIGHTS

Standard Side Member Projection: 14″
Side Member Face Width: 12″
Side Member Backing: 2×8 Pressure Treated Wood
Standard Cover Fabric: 10 oz. Vinyl
Standard Head Member Projection is 10″ Greater than Side Member Projection
Front of Header Assembly is 2×8
Top of Head Frame Has Upward Taper & Requires 2-1/2″ Clearance Above Unit Height (i.e. 11′-8″ high unit requires 11′-10-1/2″ clear at wall).
Blower Motor: 1/2 HP, 115v with Automatic Reset Thermal Overload Protection (includes NEMA 1 switch)
Guide Stripes on Head Storage Curtain on 8′-6″ Centers
Head Member Mounting Flanges Require 2″ Clearance on Either Side
Head Member Consists Fiberglass Covered Treated Wood Frame Which Supports Integral Torsion Spring-head Bag Assembly (standard head bag drop is 36″ to 48″)

Serco SI310 Inflatable Rail Shelter

This Air Inflatable Rail Shelter series is sesigned for effective sealing of a wide variety of rail loading dock applications. Available in either three-sided or four-sided versions.

DESIGN HIGHLIGHTS

Standard Projection: Up to 48″
Standard Cover Fabric: 10 oz. Vinyl
Side & Head Member Backing: 2 x 12 Pressure Treated Wood
Blower Motor: 1/2 HP, 115V with Automatic Reset Thermal Overload Protection (includes NEMA 1 switch)
Metal Blower Cover & Retraction Brackets Included.
Standard Top, Bottom & Side Member Face Width: 12″
Standard Air Tube Location 36” in on Top Left
Rail Shelter Projection is Equal to Distance From the Inside of Near Rail to Building Wall Minus 24″ (field survey) or Centerline of Track to Building Wall Minus 54″ (architectural plans)
Only One of These Projection Calculations is Required
Approximately 28″ Clearance Required Above Top of Unit for Mounting of Motor Blower & Retraction Bracket System
4-Sided Unit Should Be Sized So Bottom Is 24″ Below-dock Level (notify factory if hydraulic rail ramp is present)

Specifications

Serco SI300 Inflatable Dock Seal

The Air Inflatable Dock Shelter with Treated Wood Frames is designed for wider and taller doorways and loading docks that serve a wide variety of vehicle sizes including vehicles with extended tailgates or hydraulic lifts.

DESIGN HIGHLIGHTS

Standard Projection: 12″
Standard Cover Fabric: 10 oz. Vinyl
Side & Head Member Backing: 2×8 Pressure Treated Wood
Standard Head & Side Member Face Width: 12″
Blower Motor: 1/2 HP, 115v with Automatic Reset Thermal Overload Protection (includes NEMA 1 switch)
Metal Blower Cover Included
24″ High Guide Stripes at Bottom of Side Members
Front Opening Width is Approx. 7’-6″

Brochure